Everything You’ll Need
| Tool/Material | Laminate Flooring | Purpose |
|---|---|---|
| Utility Knife | ✔ | Cut underlayment and trim edges |
| Tape Measure | ✔ | Measure room and plank sizes |
| Straight Edge | ✔ | Make straight cuts and align |
| Pry Bar | ✔ | Remove baseboards or old floors |
| Spacers | ✔ | Keep gaps along walls |
| Tapping Block | ✔ | Tap planks together safely |
| Non-Marring Hammer | ✔ | Works with tapping block for tight fit |
| Laminate Cutter or Saw | ✔ | Cut planks to the right size |
| Knee Pads | ✔ | Protect knees while installing |
| Level | ✔ | Make sure floor is even |
| Chalk Line | ✔ | Mark straight lines |
| Underlayment Roll | ✔ (if needed) | Add cushioning and reduces noise |
| Jigsaw or Oscillating Tool | ✔ | Cut around pipes and door frames |
Step 1: Choose a Layout Pattern
Before you put down your laminate flooring, decide how to arrange the planks. Laminate doesn’t have as many pattern choices as vinyl or tile, but your layout can still change how the room looks.
Here are the top patterns for laminate flooring:
Straight Lay Pattern (Most Common)
This is the easiest and most popular way.
Planks go parallel to the longest wall or toward natural light. It gives a clean, classic look, great for most rooms.
Diagonal Pattern
Gives a more stylish look.
Planks are placed at a 45-degree angle to the walls, making small rooms look bigger or adding interest to square rooms. This method may need more cutting and extra material.
Random/Variable Stagger
Planks are staggered with different lengths in each row.
This looks like natural hardwood and avoids repeating patterns or lined-up seams.
Herringbone or Chevron (Advanced/Pro)
Some laminate floors are made for herringbone or chevron designs.
These look amazing but need precise cuts and planning. Not all laminate brands have planks for these patterns.
Step 2: Prepare the Space
Take Out Baseboards and Old Flooring
First, get rid of the baseboards and old flooring to have a clean area.
Use a pry bar to gently take off the baseboards without harming the walls, so you can use the trim again.
If you have carpet, cut it into small pieces with a utility knife and pull it up.
For tile, vinyl, or wood, follow the right steps to remove each type.
Clean and Check the Subfloor
Sweep and vacuum well to clear out dust and debris.
Look for cracks, dips, or high spots. Use a leveling compound to fill dips and sand down high spots. A flat subfloor is important for a strong laminate floor.
Put Down Underlayment
Most laminate floors need an underlayment unless they already have one.
Underlayment gives cushion, cuts down noise, and helps fix small subfloor issues.
Roll it out on the subfloor, ensuring edges touch but don’t overlap. Tape the seams well.
✅ Pro Tip: If laying over concrete, think about adding a moisture barrier under the underlayment.
Step 3: Choose an Installation Method
Laminate flooring is made for those who like to do things themselves, using a simple method: Click-Lock (Floating Floor). It usually doesn’t need glue or peel-and-stick.
Click-Lock (Floating Installation)
The Click-Lock system, also known as tongue-and-groove or interlocking, is the most popular and easy option for laminate floors. Planks click together, making a secure fit without nails or glue.
This lets the floor “float” over the subfloor, allowing it to expand and contract with changes in temperature and humidity.
Key Advantages:
- No adhesives needed — easy cleanup and fewer materials.
- DIY-friendly — perfect for beginners.
- Versatile — works over various subfloors like concrete and plywood.
Installation Tips:
- Leave a 1/4-inch expansion gap around the room’s edges using spacers. This stops buckling when the floor expands and contracts.
- Follow the manufacturer’s advice for plank alignment and clicking techniques.
- Use a tapping block and pull bar to make tight seams without harming the plank edges.
Step 4: Lay the First Row
Cut the Short Edge of the First Plank
Start by trimming the short edge of your first plank. This helps the plank fit nicely against the wall for a neat look. Use a utility knife for thin laminates or a circular saw or miter saw for thick planks.
Place the First Plank 1/4 Inch from the Wall
Put the first plank by the starting wall, leaving a 1/4-inch gap between the plank and the wall. This gap is important because laminate flooring changes with temperature and humidity.
Use Spacers to Keep the Gap
Put spacers between the wall and the floor to keep the gap steady as you lay the floor. Use these spacers all around the room.
Stagger End Joints for Strength and Look
When you start the second row, cut the first plank to be at least 6 inches shorter than the first plank of the row before. This staggers the end joints, making the floor stronger and giving it a more natural look.
Tip: Don’t line up joints across rows — it can weaken the floor and look fake.
Step 5: Cutting Planks to Fit
Straight Cuts — Score and Snap
For straight cuts (like trimming the end of a plank):
Use a utility knife to score along your marked cut line.
Snap the plank along the score for a clean break (this method works best for thinner laminates).
For thicker or tougher laminate, use a laminate cutter, circular saw, or miter saw for precise, clean cuts.
Irregular Cuts — Around Corners and Obstacles
When cutting around door frames, corners, or awkward shapes:
Use a jigsaw or oscillating multi-tool.
These tools allow precise, curved, or angled cuts that a standard saw can’t achieve.
Cutting Around Pipes
Measure the diameter of the pipe and add 1 inch to allow for expansion.
Drill a hole in the plank to fit the pipe size.
Make a straight cut from the hole to the plank’s edge.
Once installed, seal around the pipe with a bead of silicone caulk to cover the gap and prevent moisture from seeping in.
Tight Spaces — Under Door Jambs
Use a jamb saw (also called an undercut saw) to trim the bottom of the door frame.
This allows you to slide the laminate plank neatly underneath for a clean, professional look.
Pro Tip: Always wear safety goggles and work slowly when using power tools to avoid splintering the laminate or damaging surrounding materials.
| Cutting Task | Recommended Tool(s) | Technique |
|---|---|---|
| Straight cuts (length/width) | Utility knife (thin laminate) Laminate cutter or miter saw (standard) | Score and snap for thin laminate Use a saw for clean, straight cuts |
| Irregular cuts (corners, curves) | Jigsaw or oscillating multi-tool | Mark the shape, cut slowly following the line |
| Around pipes | Drill + Jigsaw or Hole saw | Drill a hole + cut a slit to the edge, leave ½” expansion gap |
| Tight spaces (door jambs) | Jamb saw (undercut saw) | Undercut the jamb to slide the plank underneath |
| Final fitting/trimming | Utility knife or laminate cutter | Trim small excess for a snug fit |
Step 6: Laying Subsequent Rows
Angle the Planks into Place
Begin each new row by angling the tongue of the plank into the groove of the previous row. Gently lower the plank until it clicks or fits snugly into position.
Use a Tapping Block and Non-Marring Hammer
For a tight, seamless fit, use a tapping block and a non-marring hammer (or mallet).
Place the tapping block against the edge of the plank.
Tap gently to close any gaps between the planks.
Never use a standard hammer directly on the laminate—this can chip or damage the edges.
Maintain the Staggered Pattern
Continue staggering the end joints by at least 6 inches in each row for both stability and a natural appearance.
Check Expansion Gaps
Keep spacers along the walls to maintain the 1/4-inch expansion gap throughout the installation.
Step 7: Finishing the Installation
Install Transition Strips
Once all planks are in place, install transition strips at doorways and where the laminate meets other flooring types. These strips:
Provide a smooth, safe transition.
Protect the edges of your laminate flooring.
Follow the manufacturer’s instructions for type and installation.
Transitioning to Other Flooring
Use the right type of transition:
T-molding for floors of equal height.
Reducer strips for transitioning to lower surfaces like tile or vinyl.
Attach transition strips to the subfloor—never directly to the laminate—leaving a 1/4-inch expansion gap to prevent buckling.
Reinstall Baseboards
Reattach baseboards, securing them to the wall, not the floor. This allows the laminate to expand and contract freely beneath.
Allow the Floor to Settle
Before moving furniture back or walking extensively on the floor:
Allow at least 48 hours for the laminate to acclimate to the room’s temperature and humidity.
Common Mistakes to Avoid When Installing Laminate Flooring
Installing in High-Moisture Areas
Laminate flooring isn’t recommended for areas with excessive moisture, like full bathrooms or laundry rooms. Water can seep into the seams, causing swelling or warping.
Using a Hammer Directly on Planks
Never use a hammer directly on the laminate. Always use a tapping block or pull bar to gently secure planks without damaging their edges.
Overlapping End Joints
Don’t align or overlap the end joints of planks in adjacent rows. This weakens the floor’s structure and can lead to gaps or uneven surfaces. Stagger the joints by at least 6 inches.
Skipping the Expansion Gap
Failing to leave a 1/4-inch expansion gap around the room’s perimeter can cause buckling as the floor expands and contracts with temperature and humidity changes.
Walking on the Floor Too Soon
Allow the laminate floor to acclimate and settle for 48 hours after installation before subjecting it to foot traffic or placing heavy furniture.
Tips for a Successful Laminate Flooring Installation
- Measure Accurately and Plan for Waste
Measure your room carefully and purchase 10% extra laminate flooring to account for cuts, mistakes, and future repairs. - Inspect Planks Before Installation
Check each plank for defects or damage before laying it. Discard or set aside any damaged pieces to maintain a high-quality finish. - Use Knee Pads for Comfort
Protect your knees by using knee pads, especially during long installation sessions. This can also help you work more efficiently. - Work Methodically and Don’t Rush
Take your time with each step, from laying the first row to cutting planks. Rushing can lead to poor fits, uneven seams, and costly mistakes. - Maintain the Recommended Expansion Gap
Always leave a 1/4-inch expansion gap around the perimeter to prevent buckling as the laminate expands and contracts.
DIY vs. Professional Laminate Flooring Installation
Many homeowners choose laminate flooring because it’s one of the most DIY-friendly flooring options available. But whether to install it yourself or hire a professional depends on your comfort level, tools, and project complexity.
DIY Installation
✅ Pros:
- Save on labor costs (typically $2 to $5 per sq ft).
- Flexibility to work at your own pace.
- Great for smaller, simple rooms.
❌ Cons:
- Requires basic tools (spacers, tapping block, saws).
- Mistakes like improper expansion gaps can lead to warping or separation.
- Time-consuming, especially for larger or irregularly shaped spaces.
Professional Installation
✅ Pros:
- Fast, precise installation.
- Experts handle subfloor prep, tricky cuts, and transitions.
- Often includes a warranty.
❌ Cons:
- Additional cost — typically adds $2 to $5 per sq ft for labor.
On average, laminate flooring installation (materials + labor) costs between $4 and $12 per square foot depending on the style and complexity. For a more detailed breakdown, check out our Laminate Flooring Cost Guide.
| Installation Method | Average Cost per Sq Ft | Pros | Cons |
|---|---|---|---|
| DIY Installation | $1.50 – $4 (materials only) | Save on labor Flexible schedule Good for small areas | Time-consuming Requires tools & skills Mistakes can be costly |
| Professional Installation | $4 – $12 (materials + labor) | Fast & precise Warranty often included Handles complex cuts & transitions | Higher upfront cost |
Do You Need Professional Help With Your Laminate Flooring Installation Project?
Now that you’ve learned how to install laminate flooring, you’re well on your way to creating a stylish, durable floor. But if you’d rather skip the heavy lifting and precise cuts, our expert team is ready to help.
We handle everything — from proper subfloor preparation to perfect plank alignment — so you can sit back and enjoy flawless, long-lasting results. We’ll also assist you in choosing the right laminate style and underlayment to match your space and budget.
Contact us today to schedule your free in-home consultation and see if we serve your area.
